- Home
- Slice Engineering
- Slice Engineering BridgeMaster Nozzles - Multiple Sizes
Slice Engineering BridgeMaster Nozzles - Multiple Sizes
Related Products
Slice Engineering Mosquito Hotend
$213.00
This hotend kit comes with: Mosquito Hotend* GammaMaster® Nozzle - 0.4 mm Mosquito Silicone Boot Boron Nitride Paste - 1 cc Hotend Mounting Hardware Hotend Wrench Set Gourmet Lollipop (Made in the USA) PLEASE NOTE: heater, thermistor, and fan are sold separately. Superior heat break performance Increased structural rigidity Larger temperatur...
Slice Engineering Magnum Mosquito Hotend
$249.00
This hotend kit includes: Mosquito Magnum Hotend* GammaMaster® Nozzle - 0.4 mm Mosquito Silicone Boot Boron Nitride Paste - 1 cc Hotend Mounting Hardware Hotend Wrench Set Gourmet Lollipop (Made in the USA) PLEASE NOTE: heater, thermistor, and fan are sold separately. The Mosquito Magnum prints up to 20% faster than any other hotend on the...
Slice Engineering Vanadium Nozzle - Multiple Sizes
Slice Engineering Vanadium Nozzle - Multiple Sizes
$48.99
Lifetime warranty against abrasion Wear resistant, plastic repellent coating High speed steel, hardened and tempered to 64 Rockwell C. Available in multiple orifice sizes Would you like an indestructible nozzle? Try ours out. With a 64 Rockwell C hardness (Vickers HV 910) minimum rating, it’s virtually unscratchable. It’s actually hard to diff...
Slice Engineering Boron Nitride Paste
Slice Engineering Boron Nitride Paste
$14.99
Thermal paste for improving conduction Acts as a release agent Use the included applicator to coat the cartridge heater hole in your 3D printer heat block. Insert the cartridge heater while the paste is still wet, then let dry. The boron nitride boosts dissipation of heat from the hot section of the cartridge heater, improving its life. Retails...
Slice Engineering Mosquito 50w Heater Cartridge
Slice Engineering Mosquito 50w Heater Cartridge
$19.45
22 mm. diameter sized to fit into a 6 mm H7 tolerance hole Leads are 1 m in length Molex connectors Available in 12V or 24V variations 50W Like upgrading the engine in your car, suddenly an unsuspecting machine can compete with the top of the line. The 50W Heater Cartridge takes your 3D printer and opens a whole new world of engineering-grade ...
Slice Engineering Thermistor High Temperature
Slice Engineering Thermistor High Temperature
$39.99
Eliminates the need for high temperature RTD's or having two separate thermistors to maintain accuracy at both the low and high end of the temperature spectrum.This is simply the highest performing thermistor on the market.Requires update of ADC table in printer firmware.15 mm long. 3 mm diameter, the de facto standard for sleeved thermistors.Hi...
Slice Engineering Nozzle Torque Wrench™
Slice Engineering Nozzle Torque Wrench™
$49.99
Specifically designed for changing nozzles 1.5 Nm torque provides correct seal to prevent leaking plastic Perfect tool for one-handed nozzle change when paired with The Mosquito Hotend™ Fits Vanadium Nozzles™ natively, with just enough wiggle room for that baked on plastic Fits other style nozzles with off-the-shelf adapters Annoying...
Slice Engineering Plastic Repellent Paint
$14.95
Got a sticky nozzle? Sick of plastic sticking to it all the time? Plastic Repellent Paint™ by Slice Engineering® is the solution for you! Plastic Repellent Paint™ is a revolutionary, water-based, PTFE nanosuspension that repels plastic from the outside of your nozzle and hot block. Which is awesome, because it prevents that annoying plastic buil...
Slice Engineering RTD PT1000 - Resistance Temperature Detector
$36.00
Pt1000 Resistance Temperature Detector (RTD) uses a platinum resistor for the ultimate in temperature sensing performance. Works with Duet 3 and other high amperage boards out of the box. Perfect for any Pt1000-compatible 3D printers. Accurate from freeze-your-butt-off cold (-50 °C) to instantly-boil-your-innards hot (500 °C) Totally linear ...
Slice Engineering Mosquito Hotend Fan | 12V-24V
$4.99
Slice Engineering Hot-End Fan High quality 25 mm box fan with dual Japanese bearings Molex Micro-Fit 3.0 connector Mounts directly to the Mosquito® Hotend, Mosquito® Magnum, or Copperhead™ with included hardware Available in 12V or 24V configurations 1 m extension cable included
Slice Engineering Copperhead Heat Sink - Various Mounts
$59.95
PLEASE NOTE: The Copperhead™ Heat Sink is only compatible with the Copperhead™ Standard Heat Break because the Copperhead™ Heat Sink uses a shank and collar mechanism (no threading) to hold onto the heat break. Here.
Slice Engineering Copperhead Heat Break - Different Variants
$54.99
Copperhead™ Heat Breaks come in multiple variants to adapt to numerous 3D printers. Use the 3D Printer Compatibility Chart below to determine which Bimetallic Heat Break™ is best suited for your application. NOTE: Only the Standard Variant fits the Copperhead™ Heat Sink Standard G2 Variant - fits Copperhead™ Heat Sink & Raise3D Pro2 Defini...