- Home
- Slice Engineering
Slice Engineering

Slice Engineering Mosquito Hotend
$157.00
This hotend kit comes with: Mosquito Hotend* GammaMaster® Nozzle - 0.4 mm Mosquito Silicone Boot Boron Nitride Paste - 1 cc Hotend Mounting Hardware Hotend Wrench Set Gourmet Lollipop (Made in the USA) PLEASE NOTE: heater, thermistor, and fan are sold separately. Superior heat break performance Increased structural rigidity Larger temperatur...

Slice Engineering Magnum Mosquito Hotend
$184.00
This hotend kit includes: Mosquito Magnum Hotend* GammaMaster® Nozzle - 0.4 mm Mosquito Silicone Boot Boron Nitride Paste - 1 cc Hotend Mounting Hardware Hotend Wrench Set Gourmet Lollipop (Made in the USA) PLEASE NOTE: heater, thermistor, and fan are sold separately. The Mosquito Magnum prints up to 20% faster than any other hotend on the...

Slice Engineering BridgeMaster Nozzles - Multiple Sizes
$26.00
Achieve peak bridging performance with the BridgeMaster® Nozzle! Copper alloy core optimized for thermal conduction Super tough, carbide based surface coating that reduces wear from abrasive filaments Forgot what size nozzle you have installed? With the BridgeMaster® Nozzle you don't need to know braille, or read a chart, the orifice size is en...

Slice Engineering Vanadium Nozzle - Multiple Sizes
$37.00
Lifetime warranty against abrasion Wear resistant, plastic repellent coating High speed steel, hardened and tempered to 64 Rockwell C. Available in multiple orifice sizes Would you like an indestructible nozzle? Try ours out. With a 64 Rockwell C hardness (Vickers HV 910) minimum rating, it’s virtually unscratchable. It’s actually hard to diff...

Slice Engineering Boron Nitride Paste
$12.00
Thermal paste for improving conduction Acts as a release agent Use the included applicator to coat the cartridge heater hole in your 3D printer heat block. Insert the cartridge heater while the paste is still wet, then let dry. The boron nitride boosts dissipation of heat from the hot section of the cartridge heater, improving its life. Retails...

Slice Engineering Mosquito 50w Heater Cartridge
$15.00
22 mm. diameter sized to fit into a 6 mm H7 tolerance hole Leads are 1 m in length Molex connectors Available in 12V or 24V variations 50W Like upgrading the engine in your car, suddenly an unsuspecting machine can compete with the top of the line. The 50W Heater Cartridge takes your 3D printer and opens a whole new world of engineering-grade ...

Slice Engineering Thermistor High Temperature
$30.00
Eliminates the need for high temperature RTD's or having two separate thermistors to maintain accuracy at both the low and high end of the temperature spectrum.This is simply the highest performing thermistor on the market.Requires update of ADC table in printer firmware.15 mm long. 3 mm diameter, the de facto standard for sleeved thermistors.Hi...

Slice Engineering Nozzle Torque Wrench™
$37.00
Specifically designed for changing nozzles 1.5 Nm torque provides correct seal to prevent leaking plastic Perfect tool for one-handed nozzle change when paired with The Mosquito Hotend™ Fits Vanadium Nozzles™ natively, with just enough wiggle room for that baked on plastic Fits other style nozzles with off-the-shelf adapters Annoying...

Slice Engineering Plastic Repellent Paint
$11.00
Got a sticky nozzle? Sick of plastic sticking to it all the time? Plastic Repellent Paint™ by Slice Engineering® is the solution for you! Plastic Repellent Paint™ is a revolutionary, water-based, PTFE nanosuspension that repels plastic from the outside of your nozzle and hot block. Which is awesome, because it prevents that annoying plastic buil...

Slice Engineering RTD PT1000 - Resistance Temperature Detector
$30.00
Pt1000 Resistance Temperature Detector (RTD) uses a platinum resistor for the ultimate in temperature sensing performance. Works with Duet 3 and other high amperage boards out of the box. Perfect for any Pt1000-compatible 3D printers. Accurate from freeze-your-butt-off cold (-50 °C) to instantly-boil-your-innards hot (500 °C) Totally linear ...

Slice Engineering Mosquito Hotend Fan | 12V-24V
$4.00
Slice Engineering Hot-End Fan High quality 25 mm box fan with dual Japanese bearings Molex Micro-Fit 3.0 connector Mounts directly to the Mosquito® Hotend, Mosquito® Magnum, or Copperhead™ with included hardware Available in 12V or 24V configurations 1 m extension cable included

Slice Engineering Copperhead Heat Sink - Various Mounts
$45.00
PLEASE NOTE: The Copperhead™ Heat Sink is only compatible with the Copperhead™ Standard Heat Break because the Copperhead™ Heat Sink uses a shank and collar mechanism (no threading) to hold onto the heat break. Here.

Slice Engineering Copperhead Heat Break - Different Variants
$41.00
Copperhead™ Heat Breaks come in multiple variants to adapt to numerous 3D printers. Use the 3D Printer Compatibility Chart below to determine which Bimetallic Heat Break™ is best suited for your application. NOTE: Only the Standard Variant fits the Copperhead™ Heat Sink Standard G2 Variant - fits Copperhead™ Heat Sink & Raise3D Pro2 Defini...

Slice Engineering Copperhead Heat Block
$25.00
PLEASE NOTE: The Copperhead™ Heat Sink is only compatible with the Copperhead™ Standard Heat Break because Slice Engineering Copperhead™ Heat Sink uses a shank and collar mechanism (no threading) to hold onto the heat break. Installation Instructions: • Copperhead™ Installation Instructions3MF: • Copperhead™ Groove Mount w/nozzle• Copperhead™...

Slice Engineering Mosquito Silicone Boot
$12.00
Boots provide long lasting protection from cooling air and plastic adhesion. The Mosquito Silicone Boot is: Made from high grade silicone for higher temperature resistance Thickly molded with internal air cavities to ensure optimal thermal insulation and tear resistance Rated to 290 °C printing temperatures Spring loaded to keep the boot hook...

Slice Engineering Mosquito Liquid
$195.00
Behold the Mosquito® Liquid - it uses the same patented technology found in the standard, air-cooled Mosquito® hotend, but optimized for liquid cooling in heated enclosures. The liquid cooling block is precision machined out of a corrosion resistant bronze alloy that allows for use with most commercially available coolants. Liquid also features ...

Slice Engineering Filament Drying Desiccant
$20.00
Activated alumina desiccant is 10x more powerful than comparable silica gel, and is non-toxic! Creates enough of a relative humidity (Rh) gradient to absorb both surface moisture and water particles captured inside the filament. Stainless steel canister is perfectly sized to fit in the center of your filament spool. Desiccant is infinitely rech...

Slice Engineering Copperhead Silicone Boot
$12.00
At long last, there is an official silicone boot for the Copperhead. And yes, it is a boot, not a sock. Socks can be flimsy, fall off, and tear easily. Boots are there for you when the rubber meets the road, providing long lasting protection from cooling air and plastic adhesion. The Copperhead Silicone Boot is: Made from high-grade silicone f...

Slice Engineering Raise3D E2 Upgrade Bundle
$232.00
It's time to unlock the full power of your Raise3D E2, with the ubiquitous Copperhead®. We've built a reputation for outfitting 3D printers with premium engineering-grade components that drastically improve performance. The result is less downtime, less wasted filament on failed prints, less tinkering, increased throughput, and higher resolutio...